Example application · Lakewood, Ohio · R1H

Example Application — 400 SF Second Floor Over an Existing One-Story Rear Wing

A filled, illustrative application packet: owner-builder affidavit, zoning worksheet, ABR narrative, before/after plates, and A/S/E/P/M/LS drawings. Use it as a shape, not as a sealed set.

R1H 50 × 175 400 SF Nov 8, 2026

1. Example project data

Owner[OWNER NAMES] — owner-builder
Address / parcel[ADDRESS], Lakewood, OH 44107 · [PARCEL]
Zone / lotR1H · 50'-0" × 175'-0" = 8,750 SF
Existing footprint1,850 SF (21.1% of lot; 35% max)
Proposed footprint1,850 SF (no increase; second floor over existing wing)
Total lot coverage2,050 SF (23.4%; 85% max)
Rear yard38'-0" existing / 38'-0" proposed; 40'-0" required → variance
Side yards7'-6" / 7'-6"; sum 15'-0" (5' min each; 15' sum)
Height18'-0" existing / 27'-0" proposed; 35'-0" max
ScopeRemove sloped/multi-sloped roof; new 400 SF second floor; bedroom 12'×16'; bath 8'×10'; closet 6'×8'; stair/hall 4'×20'; new roof; MEP; finishes.
Designer[PE], Ohio PE [LICENSE NO.]
Structural PE[NAME], Ohio PE [LICENSE NO.]

2. Filled application

Permit typeBuilding permit — residential addition
Property class1-family dwelling
ScopeSecond-floor addition over existing one-story rear wing; remove existing roof; new floor, walls, roof, stair, bedroom, bathroom; electrical, plumbing, HVAC; insulation and finishes.
ContractorOwner-builder (affidavit attached)
Valuation$[____] (materials + paid labor; confirm owner-labor treatment with the city)
ABRRequired — exterior elevation change; approval attached
Historic[Not in HPD/HP / confirmation attached]
Flood[Zone X / confirmation attached]
Energy2018 IECC compliance attached
StructuralSealed calculations and letter attached
ElectricalLoad calculation and panel schedule attached
PlumbingPlan and riser attached
HVACManual J and duct layout attached

TEMPLATE — REPLACE BRACKETS WITH REAL DATA; USE LAKEWOOD’S CURRENT FORM.

3. Zoning worksheet

ItemExistingProposedLimit / code
Principal footprint1,850 SF1,850 SF3,062.5 SF max (35%)
Total lot coverage2,050 SF2,050 SF7,437.5 SF max (85%)
Rear yard38'-0"38'-0"40'-0" min — nonconforming
Side yards7'-6" / 7'-6"7'-6" / 7'-6"5'-0" each; 15'-0" sum
Height18'-0"27'-0"35'-0" max
Front yard[__][__]Building Line Map / average

Nonconformity note: the existing rear wing is 38'-0" from the rear lot line; R1H requires 40'-0". The proposed second floor is directly above the existing footprint and does not extend the rear wall. The owner requests the City’s written determination whether this increases the nonconformity under LCO §1149.04; if it does, the BZA variance narrative applies.

4. ABR narrative

Project: 400 SF second-floor addition over existing one-story rear wing. Existing: one-story rear wing with sloped/multi-sloped roof; [siding]; [roof]; [windows]. Proposed: new second-floor volume within the existing footprint; new [gable/hip] roof at [__] pitch tying into the existing ridge/valley; [siding], [roofing], [windows], [trim], [gutters]; colors [body/trim/roof]. Height: 27'-0"; rear yard: 38'-0"; side yards: 7'-6"/7'-6". Compatibility: massing steps back from the existing ridge; window rhythm and materials match the house and block. Photos: front/side/rear/context attached.

5. Before / after plates

Illustrative before massing

Before — illustrative massing. Replace with real rear/side/context photos.

Illustrative after massing

After — illustrative massing. Replace with real photos of the completed or proposed volume.

PHOTO LOG: FRONT, SIDE, REAR, CONTEXT, ROOF BEFORE, ROOF AFTER, ADJACENT HOUSES.

6. Architectural drawings

A0.0 — Cover / general notes

A0 cover sheet

Cover sheet: project data, code matrix, sheet index, general notes.

A1.0 — Existing site plan / rear elevation

A1 existing site plan and rear elevation

Existing conditions: 50 × 175 lot, 7'-6" side yards, 38'-0" rear yard, one-story rear wing with multi-slope roof.

A2.0 — Proposed rear elevation / second-floor plan

A2 proposed elevation and floor plan

Proposed 20 × 20 second floor: bedroom, bath, closet, stair/hall, egress window.

A3.0 — Roof plan / multi-slope tie-in

A3 roof plan

Roof plan: slopes, ridge, valleys, ice barrier, flashing, ventilation, gutters.

A4.0 — Wall / roof section

A4 wall and roof section

Section: existing first floor, new floor framing, new second floor, new roof, insulation/air sealing.

7. Structural drawing

S1 foundation and framing plan

S1.0: new footings, beam, columns, joists, load path, shoring and inspection notes. Seal by Ohio structural PE.

8. Electrical drawing + panel schedule

E1 electrical plan

E1.0: lighting, receptacles, switches, smoke/CO, bath GFCI, panel location.

CircuitDescriptionAmpsProtectionWire
1Bedroom receptacles15AFCI14/2
2Bedroom lighting15AFCI14/2
3Bath receptacles20GFCI12/2
4Bath lighting/exhaust15AFCI14/2
5Smoke/CO15AFCI14/3
6Spare20—12/2

Load summary: general lighting 1,200 VA; small appliance 3,000 VA; laundry 1,500 VA; bath 1,500 VA; bedroom 1,200 VA; HVAC 2,400 VA; total 10,800 VA; demand 45 A at 240 V. Existing service 100 A; new subpanel 60 A. Verify with the actual service calculation.

9. Plumbing drawing + riser

P1 plumbing plan and riser

P1.0: WC 3", lav 1-1/2", shower 2"; 2" vent; 1/2" supplies; cleanout; access panels.

10. HVAC drawing + load summary

M1 HVAC plan

M1.0: equipment, supply/return, bath exhaust, fresh air, condensate. Manual J attached.

ItemValue
Area400 SF
Cooling12,000 BTU/hr
Heating5 kW
Supply / return200 CFM / 200 CFM
Bath exhaust50 CFM to exterior

11. Life safety / egress

LS1 life safety plan

LS1.0: EERO 5.7 SF, 24" × 20", sill ≤44"; stair 36" clear, 10" tread, 7-3/4" riser; guard 36"; smoke/CO.

12. Inspection card

InspectionWhenCall
Pre-construction / permit postingBefore work[ ]
Footing/foundationBefore concrete[ ]
FramingBefore covering[ ]
Electrical roughBefore insulation[ ]
Plumbing roughBefore insulation[ ]
HVAC roughBefore insulation[ ]
Insulation / air sealingBefore drywall[ ]
Final building / electrical / plumbing / HVACAt completion[ ]
Smoke/COAt final[ ]

13. Submittal checklist

[ ]Building permit application, signed by owner
[ ]Owner-builder affidavit
[ ]Unpaid family labor acknowledgment (recommended)
[ ]Contractor registration / insurance / BWC for paid subs
[ ]Zoning envelope worksheet
[ ]ABR approval letter
[ ]BZA variance approval (if required)
[ ]Historic/HP approval (if applicable)
[ ]Plan set A0–LS1
[ ]Sealed structural calculations and letter
[ ]Electrical load calculation / panel schedule
[ ]Plumbing plan / riser
[ ]HVAC Manual J / duct layout
[ ]Energy compliance
[ ]Survey / site plan
[ ]Fees

14. What is missing from the public record

Lakewood publishes ABR agendas and minutes, which often include site plans, elevations, and photos. It does not publish the full building-permit set with sealed architectural, structural, electrical, plumbing, and HVAC drawings. To see a real full set for a similar project, request the permit file for a specific address through the Lakewood Building Department or review the plans at the counter with the owner’s permission. The drawings on this page are representative, not a real applicant’s sealed set.

← Back to the Lakewood document pack